Just How to Replace a Bathtub in Your Bathroom
Just How to Replace a Bathtub in Your Bathroom
Blog Article
Do you find yourself interested in info around How to Install a Bathtub Yourself?
Setting up a bath tub isn't precisely rocket science, however it does require solid plumbing, carpentry, and occasionally, tiling skills. Replacing an old bathtub with a brand-new one is additionally a moderately challenging project. If the old tub is easily available, the task can move quickly; if you have to open up a wall surface to eliminate the old tub and place the brand-new bath tub, the job is much harder. In either case, the task is within a residence handyman's abilities, although you will need an assistant to vacate the old tub and set in the new one. Ensure you have certified on your own for the task and fit trying it. Instead of hiring a contractor to take control of a halfway-completed job, it is better to consider employing one prior to you begin. Opportunities are you might need a specialist plumber to make tube links.
This short article will certainly assist you install a brand-new tub in your restroom if you have actually already acquired a brand-new bathtub and do not need to change the setup of your previous supply of water pipelines.
Your devices and product checklist need to comprise the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you should do is separate the supply of water. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing taps can be fairly problematic as a result of the restricted gain access to that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a fabric all set for the remaining water that will certainly come from the pipes. When the supply pipelines have been gotten rid of, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming during this procedure. Once the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old securing substance.
Before carrying on to fit the brand-new taps, compare the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will call for decreasing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in place in between the tap and the sink. Safeguard the tap in place with the supplier given backnut. When the tap is securely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal tap ports. The previous kind should be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Tub
Making use of both wood boards under its feet, place the bathtub in the needed position. The wooden boards are practical in equally spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto four little factors.
The following objective is to make sure that the bath tub is leveled all round. This can be attained by examining the level and also adjusting the feet on the bathtub until the spirit level reads level.
To install taps, fit the bottom of the furthest flexible faucet connector to the appropriate supply pipe by making a compression join; after that do the very same for the various other faucet.
Activate the water and also examine all joints as well as brand-new pipework for leaks as well as tighten them if required. Fill up the bathtub and also check the overflow electrical outlet and also the regular electrical outlet for leakages.
Lastly, repair the bath paneling as described in the manufacturer's instruction manual. Tiling and securing around the bath tub must wait up until the tub has actually been utilized at least once as this will certainly settle it into its last placement.
Getting ready for the Installation
To start with, the sustaining framework supplied with the bathroom needs to be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is important to make sure that if the tap features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to prevent pressure on the tub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its final setting.
Tiling Around the Bathtub
In the area where the bathroom satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split an inflexible seal, triggering the water to pass through the wall in between the bath as well as the tiling, bring about complications with moisture and possible leakages to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your fixtures as well as fittings. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to securing, to allow for the motion experienced when the bathtub is in use. The sealant can split rather early if you do not consider this activity prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally easily readily available on the market. It is recommended to fit the ceramic tiles making use of water-resistant or water resistant glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed our section about How to Install a Bathtub. Thanks a ton for taking a few minutes to read through our piece. Appreciated our blog posting? Please share it. Help another person check it out. Thanks for your time. Please stop by our blog back soon.
Check Us Out Report this page